Dunkermotoren BG65X50-CI GPL65 7.66:1 DEK Horizon Camera Y Geared Motor 185003

Dunkermotoren BG65X50-CI GPL65 7.66:1 DEK Horizon Camera Y Geared Motor 185003

The Dunkermotoren BG65X50-CI GPL65 Camera Y Geared Motor, DEK part number 185003, is a precision motion component used in compatible DEK stencil printing equipment. It is installed in the camera Y-axis positioning mechanism, where it provides controlled movement required for camera travel, alignment positioning, and vision-related machine operations.

The assembly combines the BG65X50-CI brushless DC motor with a GPL65 gearbox and 7.66:1 reduction ratio. Dunkermotoren documentation specifies the BG65X50-CI with 24 VDC nominal voltage, 100 W nominal power, 5.6 A nominal current, and approximately 3100 rpm rated motor speed.

DEK spare-parts references identify 185003 specifically as the Camera Y motor with BG65X50-CI and a 7.66:1 gearbox, helping buyers distinguish it from visually similar Camera X and print carriage motor assemblies.

Main Product Identification

The electrical specifications above correspond to the BG65X50-CI motor platform, while the 7.66:1 gearbox and Camera Y application correspond specifically to DEK part 185003.

Cause

Why May the Camera Y Geared Motor Need Replacement?

The camera positioning mechanism performs repeated movements throughout stencil printer operation. Long production cycles, frequent acceleration and deceleration, mechanical resistance, contamination, gearbox wear, or electrical connection problems can gradually affect motion performance.

Typical symptoms that may require inspection include:

• Camera Y axis fails to move normally.
• Camera travel becomes intermittent.
• Positioning takes longer than usual.
• Unusual mechanical noise appears during movement.
• Gearbox backlash increases.
• Motor temperature becomes abnormally high.
• The printer reports camera-axis or positioning errors.
• Camera movement stops during initialization.

These symptoms do not always mean that the motor itself has failed. The drive mechanism, cables, connectors, control electronics, belts, guides, and related position-control components should also be checked before replacement.

Solution

When DEK part 185003 is confirmed as faulty, replacing it with the correctly matched BG65X50-CI GPL65 7.66:1 Camera Y geared motor configuration helps restore the mechanical drive required by the camera Y-axis system.

Correct identification is especially important because several DEK motors use similar motor housings.

For purchasing confirmation, check all of the following:

Matching only the motor family is not recommended. The gearbox ratio, installation position, connector, shaft, and DEK spare-part number should be verified together.

Specifications

Motor Technical Specifications

BG65X50-CI motor specifications are based on Dunkermotoren technical documentation.

DEK Application Specifications

DEK spare-parts lists describe 185003 as the Camera Y BG65X50-CI motor with 7.66:1 gearbox.

Related DEK Motor Reference Comparison

This comparison is important because 185002, 185003, and 185004 may appear physically similar but are assigned to different machine functions. The print carriage version also uses a different gearbox ratio.

Application

The DEK 185003 geared motor is primarily used in the camera Y-axis positioning mechanism of compatible DEK stencil printing equipment.

It is commonly referenced for DEK Horizon-family printer applications, including configurations such as Horizon 01i, 02i, 03iX, 01iX, Horizon 8, Horizon 9, Neo Horizon 03iX, and related DEK printer platforms. Exact compatibility should always be confirmed using the machine configuration and original motor label before ordering.

Typical Application Scenarios

• SMT stencil printer maintenance.
• Camera Y-axis motor replacement.
• Vision positioning mechanism repair.
• Printer refurbishment.
• Preventive maintenance.
• Production-line spare-parts inventory.
• Used DEK equipment rebuilding.
• Camera movement fault troubleshooting.
• Electronics manufacturing equipment servicing.

The motor itself does not perform image recognition. Its role is to provide the mechanical movement required to position the camera system along the designated axis.

How It Works

1. Motion Command

The printer control system requests movement of the camera assembly to a specified Y-axis position.

2. Brushless Motor Rotation

The BG65X50-CI converts electrical input into controlled rotational movement.

The brushless design removes the conventional carbon-brush commutation system and is suitable for industrial equipment requiring repeated motion cycles.

3. Gear Reduction

Motor rotation is transferred into the GPL65 gearbox.

The 7.66:1 reduction ratio reduces output speed and adapts motor rotation for the mechanical requirements of the camera positioning mechanism.

4. Mechanical Transmission

The gearbox output drives the connected camera Y-axis transmission components.

5. Camera Positioning

The camera carriage travels to the position required by the printer control sequence.

The geared motor therefore functions as one part of a complete system including the controller, mechanical transmission, guides, cables, sensors, and camera assembly.

Why Correct Gear Ratio Matters

The gearbox should not be treated as an interchangeable accessory.

Different reduction ratios produce different relationships between motor rotation and mechanical output.

For example:

Installing a motor with the wrong gearbox can result in unsuitable speed, movement characteristics, or mechanical behavior.

For this reason, always verify the complete motor and gearbox assembly rather than ordering only by the BG65X50-CI designation.

How To Choose

Step 1. Confirm Part Number

Look for:

185003

This is the most important DEK reference for this Camera Y configuration.

Step 2. Confirm Motor Label

The motor should correspond to:

BG65X50-CI

Do not select a different BG65 model only because the housing looks similar.

Step 3. Confirm Gearbox

Check:

GPL65

Step 4. Verify Reduction Ratio

The required configuration is:

7.66:1

Step 5. Confirm Application

Make sure the required replacement is for:

Camera Y Axis

Do not confuse it with Camera X, print carriage, rising table, rail width, paper-cleaning, or other printer motors.

Step 6. Compare Physical Details

Before ordering, compare:

• Motor label.
• Gearbox marking.
• Electrical connector.
• Cable direction.
• Output shaft.
• Mounting holes.
• Installation position.
• Existing motor photos.

Recommended Inquiry Information

Providing complete technical information reduces the risk of receiving an incorrect motor version.

Maintenance and Replacement Notes

Before installation, technicians should inspect the connected mechanism for excessive resistance, contamination, damaged belts, worn guides, or abnormal mechanical loading.

After replacement:

• Check connector installation.
• Verify cable routing.
• Confirm mounting screws.
• Inspect shaft coupling.
• Perform machine initialization.
• Check Camera Y movement.
• Run positioning tests.
• Perform calibration when required.

If the replacement motor becomes unusually hot or noisy, stop operation and investigate mechanical resistance, wiring, and machine control conditions.

FAQ

Q1. What is DEK part number 185003 used for?

DEK 185003 is a BG65X50-CI geared motor used in the Camera Y positioning mechanism of compatible DEK stencil printers. It provides the mechanical drive required to move the camera system along the Y direction.

Q2. What is the gearbox ratio of the 185003 motor?

The DEK 185003 Camera Y motor uses a 7.66:1 gearbox ratio. This ratio should be verified before replacement because other BG65X50-CI motor assemblies may use different reductions.

Q3. Is 185002 the same as 185003?

No. Both are commonly listed with BG65X50-CI and 7.66:1 gearbox configurations, but 185002 is identified as the Camera X motor while 185003 is the Camera Y motor.

Q4. Can I order by BG65X50-CI only?

It is better to confirm the complete configuration. Please verify BG65X50-CI, GPL65, 7.66:1 ratio, DEK part 185003, Camera Y application, connector, shaft, and mounting arrangement before ordering.

Q5. What should I send for compatibility confirmation?

Please provide the part number, printer model, motor nameplate photo, gearbox marking, connector photo, installation photo, and required quantity. These details help confirm the correct replacement configuration before quotation.

Contact Us

Need a Dunkermotoren BG65X50-CI GPL65 7.66:1 DEK Camera Y Geared Motor 185003 for printer maintenance or replacement?

Please send:

• Part number.
• Motor model.
• Machine model.
• Motor label photo.
• Gearbox photo.
• Connector photo.
• Required quantity.
• Required condition.
• Delivery destination.

We can assist with model verification, stock confirmation, quotation preparation, related DEK printer parts, and consolidated SMT spare-parts purchasing.

Brand names and part numbers are used only for product identification and compatibility reference.