FUJI XB03062 X-Axis Ball Screw for M6 II Placement Machine with Bidirectional Linear Movement

FUJI XB03062 X-Axis Ball Screw for M6 II Placement Machine

The FUJI XB03062 X-axis ball screw is a precision mechanical transmission component used in the X-axis motion system of the M6 II pick-and-place machine. It transfers motor rotation into controlled linear movement, enabling the machine carriage to travel accurately across the working area during component placement operations.

Part number XB03062 is identified in public spare-parts listings as a ball screw, while international trade records describe it as a spare part used for a FUJI SMD production line.

This component is intended for machine maintenance, motion-system repair, production-line refurbishment, and preventive spare-parts inventory. A correctly selected ball screw helps restore smooth axis movement, reduce abnormal vibration, and support consistent positioning performance. Before ordering, customers should confirm the complete part number, machine series, installation position, shaft-end configuration, nut structure, and current component photographs.

The X-axis is one of the primary motion directions in an automated placement machine. During production, the related drive system must perform repeated acceleration, positioning, deceleration, and return movements. The ball screw therefore operates as a critical mechanical link between the driving mechanism and the moving carriage.

A ball screw generally contains a screw shaft, nut, and circulating balls. The rolling-ball structure converts rotational movement into linear motion while maintaining relatively low friction and controlled positioning. Official THK and NSK technical information describes this conversion principle and the use of ball screws for accurate linear positioning in industrial machinery.

When the installed component becomes worn, contaminated, damaged, incorrectly lubricated, or mechanically misaligned, the machine may experience unstable movement. Early replacement can help prevent a minor motion problem from developing into a larger repair involving bearings, gears, holders, servo components, or adjacent linear guides.

Ball screws used in high-cycle placement equipment are exposed to repeated motion, variable acceleration, production dust, lubricant aging, and long operating hours. Failure is usually caused by a combination of mechanical wear and maintenance conditions rather than one isolated issue.

The following conditions may indicate that the existing X-axis ball screw or related support components require inspection:

A motion alarm does not always prove that the ball screw itself is defective. The servo motor, driver, encoder cable, gear, bearing holder, linear guide, stopper, lubrication path, sensor, or software calibration may produce similar symptoms. A systematic inspection is recommended before final part replacement.

The XB03062 ball screw provides a focused replacement option for restoring the X-axis mechanical transmission system of the specified M6 II configuration. It is suitable for maintenance teams that need to repair a worn motion axis without replacing the complete machine module.

The recommended solution includes more than supplying the component. Correct identification, inspection, packing, installation preparation, and post-installation verification are equally important.

The XB03062 identification allows purchasing teams to manage quotations, inventory, machine records, and maintenance documentation more accurately. Part-number confirmation reduces the risk of ordering a similar-looking but incompatible ball screw.

The component is intended for the X-axis transmission position specified for the M6 II machine configuration. Its application should still be verified because machine revisions, module versions, and previous modifications can affect compatibility.

A properly installed ball screw supports smooth conversion of motor rotation into controlled linear movement. Rolling balls circulate between the shaft and nut, helping reduce sliding friction compared with a conventional sliding screw structure.

Replacing the worn transmission component can be more economical than replacing a complete motion module, especially when the motor, frame, guide rails, sensors, and control system remain serviceable.

Factories operating multiple placement machines can keep XB03062 as a planned maintenance spare. This approach can reduce waiting time when axis wear is discovered during scheduled service.

The component can be prepared for international industrial-parts purchasing with identification labels, protective wrapping, reinforced packaging, and documentation according to the confirmed order.

Customers can provide old-part photographs, machine serial information, installation position, and dimensional references. These details help identify possible machine-version differences before shipment.

When required, the ball screw can be quoted together with related holders, bearings, collars, gears, retainers, fasteners, or other X-axis maintenance components, subject to exact machine configuration.

Exact dimensional values should be confirmed from the existing component, technical drawing, or machine record because unverified measurements should not be used for final installation.

The XB03062 ball screw is intended for the X-axis motion system of the FUJI M6 II pick-and-place machine configuration specified by the buyer. Its primary role is to transmit motor-driven rotational force into linear carriage movement.

The part is suitable for facilities operating automated SMT placement equipment, including:

The X-axis drive motor generates rotational movement. This rotation is transferred to the ball screw through the machine’s connected drive structure, which may include a gear, coupling, bearing support, or other machine-specific parts.

Inside the ball nut, precision balls roll between the helical grooves of the screw shaft and nut. As the shaft rotates, the ball nut and attached machine carriage move linearly along the axis. The balls circulate through a return path so that continuous movement can occur.

This rolling-contact mechanism is widely used because it can provide efficient motion conversion and accurate positioning. THK states that balls roll between the shaft and nut, while NSK describes ball screws as components that convert rotation into linear motion for accurate positioning.

The ball screw cannot operate independently. Its performance depends on the condition and alignment of the complete axis system.

FUJI maintenance material for M3 and M6 X-axis ball-screw replacement describes work involving the motor, gear, bearings, bearing retainers, collars, and backlash checks, showing why the complete transmission system should be inspected rather than replacing only one part.

Installation should be completed by trained SMT equipment maintenance personnel. The following information is a general reference and does not replace the applicable machine service manual.

1. Power off the equipment and follow the factory lockout procedure.
2. Record the original installation orientation before removing the old part.
3. Protect cables, sensors, covers, and nearby precision components.
4. Do not strike the precision shaft with a steel hammer.
5. Keep the ball nut installed on the shaft unless the design specifically permits separation.
6. Avoid applying side force to the shaft or nut.
7. Install the support bearings and holders in the correct orientation.
8. Tighten fasteners gradually and according to the service procedure.
9. Confirm alignment before fully tightening the connected structures.
10. Apply only the correct type and quantity of lubricant.
11. Rotate the mechanism slowly to check for binding.
12. Inspect the full stroke before returning the machine to automatic operation.

Maintenance frequency should be determined by machine operating hours, production environment, placement speed, contamination level, lubrication condition, and the equipment manufacturer’s service instructions.

• Do not drop the ball screw.
• Do not lift it only by the nut body.
• Do not place heavy objects on the shaft.
• Do not expose the component to dust, cutting particles, or moisture.
• Do not wipe away protective oil until installation preparation begins.
• Do not mix lubricants without checking compatibility.
• Do not disassemble the ball nut without the correct transfer tool.
• Do not rotate the nut beyond the threaded travel area.
• Do not force installation when resistance is detected.
• Do not use an unverified part based only on visual similarity.

The first identification point should be XB03062. Check the number on the old part, machine spare-parts record, maintenance document, purchasing history, or packaging label.

Confirm that the machine is the M6 II configuration. Similar machine names, different module generations, and previous mechanical modifications can affect the required component.

Verify that the required component is installed on the X-axis. Do not confuse it with another axis ball screw or conveyor transmission component.

Customers should compare:

“XB03062 ball screw” may refer to the main screw-and-nut component only. Buyers should clearly state whether they also require bearings, gears, holders, collars, retainers, bolts, or other related parts.

Before quotation, confirm whether the project requires:

• New original supply where available
• Qualified new compatible supply
• Refurbished supply where specifically accepted
• Exchange or repair service where available
• Complete axis maintenance set

The final condition and source should be written clearly in the quotation and purchase agreement.

For urgent line recovery, provide the required delivery date, destination country, quantity, and preferred transport method. For preventive maintenance, provide an annual spare-parts forecast to improve supply planning.

For accurate quotation and compatibility checking, please provide the following:

Long precision components require appropriate packaging to reduce transport risk.

Clear communication is essential for machine-specific mechanical parts. Quotations should identify the part number, product condition, quantity, supply scope, and application.

Customers can combine ball screws with other placement-machine parts in one inquiry, helping reduce repeated purchasing work and shipment handling.

When production is stopped, rapid confirmation is more important than general product information. Providing the machine model, part number, photographs, and quantity allows faster checking.

Single-piece maintenance orders and multi-piece preventive-stock orders can be handled according to available inventory.

Industrial spare parts can be packed for international transport with attention to moisture protection, shaft support, and impact resistance.

Customers operating multiple SMT lines can prepare equipment-based spare-parts lists covering nozzles, feeders, motors, drivers, sensors, belts, filters, cylinders, ball screws, guides, and other maintenance parts.

XB03062 is supplied as an X-axis ball screw for the specified M6 II pick-and-place machine application. Because machine versions or previous modifications may differ, please provide the old-part photographs, machine label, and installation details for final compatibility confirmation before ordering.

The standard quotation should clearly state the included supply scope. The XB03062 ball screw may be quoted separately, while bearings, gears, holders, collars, retainers, and fasteners can be checked according to the customer’s exact maintenance list and machine configuration.

Check mechanical resistance, abnormal noise, lubrication, backlash, bearings, linear guides, motor connection, encoder feedback, and servo load. An X-axis alarm can also originate from electrical or control components, so a complete diagnosis is recommended before replacing the ball screw.

Please provide part number XB03062, machine model M6 II, quantity, product condition requirement, destination country, delivery urgency, old-part photographs, and any required related components. Clear photographs of both shaft ends and the ball nut are especially useful.

Yes. The product is suitable for planned spare-parts inventory, machine refurbishment, and emergency maintenance preparation. Customers operating several M6 II machines can provide an annual quantity forecast so stock, packaging, consolidated shipping, and delivery schedules can be discussed in advance.

For price, stock status, delivery time, product condition, compatibility confirmation, or related X-axis parts, please send your inquiry with the following information:

• Part number: XB03062
• Machine model: M6 II
• Required quantity
• Photographs of the existing ball screw
• Machine nameplate photograph
• Required product condition
• Related parts list
• Destination country
• Expected delivery date

Our sales team will review the information and prepare an appropriate quotation for maintenance, refurbishment, emergency replacement, or preventive spare-parts purchasing.

Send your inquiry today for XB03062 availability, configuration checking, and international shipment support.