Panasonic FL100 N510059330AA Fluorinated Grease for CM402 CM602 NPM

Panasonic FL100 N510059330AA is a specialized fluorinated grease developed for designated lubrication points in CM402, CM602, and compatible NPM series pick-and-place machines. The product label identifies it as grease containing synthetic oil, fluoropolymer material, and a volatile fluorinated solvent. It is intended to support stable lubrication, controlled mechanical friction, and smooth movement of selected precision components during routine or preventive machine maintenance.

Unlike unidentified general-purpose lubricants, FL100 is recognized by the clear model FL100 and part number N510059330AA, helping purchasing and engineering teams reduce selection errors. Before application, users must shake the container vertically and stir the contents thoroughly. The container should be sealed immediately after use because the product contains a volatile solvent. Application quantity, lubrication position, and maintenance interval must follow the relevant machine service manual.

Modern SMT pick-and-place machines depend on repeated high-speed mechanical movement. Shafts, guides, bearings, sliding structures, drive assemblies, and other precision mechanisms must operate smoothly while maintaining accurate positioning.

During long production cycles, existing grease may gradually:

• Move away from the primary contact area.
• Become contaminated by dust or foreign particles.
• Lose part of its volatile solvent during storage.
• Mix with an unsuitable maintenance material.
• Spread beyond the required lubrication position.
• Become insufficient after component replacement or cleaning.
• Remain in service longer than the recommended interval.

Correct grease selection is therefore an important part of preventive maintenance.

The following conditions may indicate that a lubrication inspection is required:

Lubrication should be evaluated as part of a complete maintenance procedure. Grease cannot repair worn bearings, damaged guides, incorrect alignment, loose fasteners, or faulty sensors.

FL100 provides a clearly identifiable lubrication material for machine positions that specify this model or part number. Using the correct grease helps maintenance teams standardize procedures and reduce the risk of applying unidentified lubricants.

A controlled maintenance process should include:

1. Confirm the complete machine model.
2. Identify the exact lubrication position.
3. Verify that FL100 or N510059330AA is specified.
4. Inspect the container and product label.
5. Prepare clean, dedicated application tools.
6. Shake the container up and down before opening.
7. Stir the contents thoroughly before application.
8. Apply only the required amount.
9. Keep grease away from sensitive machine components.
10. Remove unnecessary excess grease.
11. Seal the container immediately after use.
12. Record the maintenance date and technician information.

Different industrial greases may use different base oils, polymers, thickeners, solvents, and additives. Even when two products look similar, they may not have the same compatibility or mechanical performance.

Potential risks of an unverified substitute include:

• Increased movement resistance.
• Grease separation.
• Material incompatibility.
• Reduced lubrication stability.
• Contamination of precision mechanisms.
• Changes in machine maintenance results.
• Difficulty tracing the lubricant used.
• Inconsistent procedures between technicians.

When the maintenance documentation specifies FL100 or N510059330AA, the same identification should be used for purchasing and application.

According to the product label, FL100 contains a synthetic-oil lubricating base, fluoropolymer material, and a volatile fluorinated solvent.

Exact material percentages, viscosity, package weight, shelf life, and full operating-temperature range should be confirmed from the actual product label, batch document, or technical safety sheet.

FL100 N510059330AA is commonly selected for specified lubrication points in:

• CM402 pick-and-place machines.
• CM602 pick-and-place machines.
• Designated NPM series placement machines.
• Compatible placement modules requiring FL100.
• Precision mechanical assemblies identified in maintenance documentation.
• Machine refurbishment and overhaul projects.
• Preventive maintenance service kits.

Compatibility should not be determined only by the machine family name. Different machine generations, serial-number ranges, modules, heads, and mechanical positions may require different lubrication products.

The product is suitable for procurement by companies involved in:

• Consumer electronics manufacturing.
• Automotive electronics production.
• Communication equipment assembly.
• Industrial control product manufacturing.
• LED and display electronics production.
• Medical electronic equipment assembly.
• Semiconductor-related manufacturing.
• Contract electronics manufacturing.
• SMT equipment maintenance.
• Pick-and-place machine refurbishment.
• Electronic manufacturing equipment distribution.
• International SMT spare-parts supply.

FL100 forms a lubricating layer between designated mechanical contact surfaces. This layer helps reduce direct surface contact during sliding, guiding, rotating, or repeated precision movement.

In a high-speed placement machine, moving mechanisms may complete many operating cycles during a production shift. Correct lubrication supports smoother movement and helps maintain stable mechanical performance.

The product should only be applied to the required maintenance position. It must not enter nearby optical, electrical, pneumatic, vacuum, conveyor, or component-handling systems.

The product label instructs users to shake the container vertically and stir the contents thoroughly before application.

This procedure is important because:

• The product contains a volatile solvent.
• Grease components may become uneven during storage.
• Thorough mixing supports consistent application.
• Proper preparation helps maintain the intended product condition.

Do not apply the product directly from a container that has remained stored for a long period without following the mixing instructions.

The product contains a volatile solvent. Leaving the container open may allow part of the solvent to evaporate.

Immediate sealing helps:

• Maintain product consistency.
• Reduce unnecessary solvent loss.
• Prevent dust from entering.
• Prevent moisture contamination.
• Protect the remaining grease.
• Support longer storage stability.

The label indicates that a small reduction in quantity may occur during long-term storage as the solvent gradually evaporates. It also states that the active lubricating ingredients do not evaporate and the lubricating effect remains unchanged.

Applying more grease than required does not necessarily improve machine performance.

Excess grease may:

• Spread into nearby machine mechanisms.
• Collect dust and foreign material.
• Increase mechanical resistance.
• Reach sensors or electrical components.
• Contaminate belts or vacuum passages.
• Make future inspection more difficult.

The correct quantity should be determined from the applicable maintenance procedure.

The required grease model should be:

FL100

Do not identify the product only by container appearance or label color.

The ordering part number should be:

N510059330AA

Include both FL100 and N510059330AA in the inquiry to reduce purchasing errors.

Provide the complete equipment identification:

• CM402.
• CM602.
• Specific NPM model.
• Module version.
• Head configuration.
• Machine serial number when required.

A pick-and-place machine may use different grease products at different mechanical positions.

Confirm the lubrication point through:

• Machine maintenance manual.
• Service documentation.
• Lubrication diagram.
• Previous product label.
• Qualified maintenance technician.
• Photographs of the mechanical position.

For an accurate quotation, provide:

1. Product model FL100.
2. Part number N510059330AA.
3. Complete machine model.
4. Required quantity.
5. Destination country.
6. Postal code.
7. Expected delivery date.
8. Preferred shipping method.
9. Packaging or label requirements.
10. Other SMT spare parts required in the same shipment.

• Stop the machine according to the factory safety procedure.
• Isolate electrical, pneumatic, or mechanical energy when required.
• Confirm the specified lubrication point.
• Check the FL100 model and N510059330AA part number.
• Wear suitable eye and skin protection.
• Prepare clean, dedicated application tools.
• Inspect the container for visible damage or contamination.
• Clean the surrounding maintenance area.
• Review the specified application quantity.
• Prepare a maintenance record.

• Shake the container up and down.
• Stir the contents thoroughly.
• Use a clean applicator.
• Apply only to the designated surface.
• Avoid excessive quantities.
• Keep grease away from sensors and connectors.
• Avoid conveyor belts and vacuum passages.
• Do not return used grease to the container.
• Do not mix with unidentified grease.
• Prevent fibers, dust, water, or metal particles from entering.

• Inspect grease distribution.
• Remove excess grease where necessary.
• Restore machine guards and covers.
• Move or test the mechanism according to the service procedure.
• Observe movement, noise, resistance, and alarms.
• Stop the test if abnormal operation remains.
• Seal the FL100 container immediately.
• Clean the application tools.
• Record the maintenance date.
• Schedule the next inspection.

Used grease, contaminated cleaning materials, application tools, and empty containers must be handled according to applicable local laws.

Do not discharge the product into:

• Drains.
• Rivers.
• Soil.
• Factory wastewater.
• Public sewage systems.
• Areas where it may reach aquatic environments.

The product label states that the material may be harmful to aquatic life. Consult an authorized waste processor when local regulations require professional disposal.

After receiving the goods, the buyer should:

1. Inspect the outer carton.
2. Confirm the received quantity.
3. Verify the FL100 model.
4. Verify part number N510059330AA.
5. Check the container for leakage.
6. Compare the label with pre-shipment photographs.
7. Confirm the packaging condition.
8. Store the product correctly.
9. Keep it separated from other grease.
10. Report any discrepancy before use.

FL100 is commonly supplied for designated lubrication positions in CM402, CM602, and compatible NPM series pick-and-place machines. The exact machine version and lubrication point must be confirmed through the applicable maintenance documentation.

An unidentified general-purpose grease should not replace FL100 without technical approval. Different grease products may use different oils, polymers, additives, solvents, and temperature-performance characteristics that can affect machine operation.

The label instructs users to shake the container vertically and stir the contents thoroughly. This helps distribute the grease components and volatile solvent evenly before application.

Seal the container immediately after use. Store it in a dark, clean, dry place protected from direct sunlight, excessive heat, dust, moisture, and foreign materials.

Please provide the FL100 model, N510059330AA part number, machine model, required quantity, destination country, postal code, expected delivery date, and any label or packaging requirements.

For current availability, technical identification, export packaging, and a competitive quotation, please send:

• Product model: FL100.
• Part number: N510059330AA.
• Complete machine model.
• Required quantity.
• Destination country and postal code.
• Expected delivery date.
• Preferred shipping method.
• Packaging and label requirements.
• Photographs of the previously used product, when available.
• Additional SMT spare parts required for combined shipment.

We support electronics manufacturers, EMS factories, SMT equipment maintenance companies, machine refurbishment businesses, distributors, and international spare-parts buyers.

Send your inquiry now to confirm compatibility, available quantity, delivery time, packing method, and quotation.

Brand names, machine models, and part numbers are used only for product identification and compatibility reference. Buyers should confirm the exact machine configuration, lubrication position, service requirement, and safety documentation before ordering or using the product.